AZTools.us

Audio Format Converter, Speed & Volume Booster

Waveform + speed & gain dials Speed & volume conversion

Adjustments

Load a file to unlock this tool’s controls:

Waveform + speed & gain dials

Runs directly on the web inside your browser. Your original file is never modified or uploaded.

How Audio Format Converter, Speed & Volume Booster Works

This converter turns an MP3, WAV, M4A, OGG, FLAC, AAC or Opus file into MP3, M4A, Opus or WAV in your browser. While converting you can also trim the file, change its speed from half to double with or without changing the pitch, and raise the volume of a quiet recording without clipping.

How to convert an audio file

  1. Drop the audio file onto the workspace.
  2. Pick the target in the format menu next to the export button. Formats your browser cannot encode are marked “not supported in this browser” and cannot be selected.
  3. Optionally drag the amber handles to convert only part of the file. Only the selection is exported.
  4. Set “Speed” and “Volume” if needed, and choose a bitrate under “Quality”. Press “Play selection” to hear the result.
  5. Press the export button, for example “Export .MP3”. The summary shows the length, codec, bitrate and sample rate of the file you got.

Output formats

Mono stays mono and stereo stays stereo in every format. A 5.1 or 7.1 file is mixed down to stereo with the ITU-R BS.775 coefficients: centre and surround channels at −3 dB, the LFE (subwoofer) channel left out. If the sum would clip, the whole mix is lowered and the note under the waveform says by how much.

When a format needs a different sample rate, the export summary says “resampled from …”. FLAC can be opened but not exported; use WAV if you need an uncompressed file. Converting a lossy file such as MP3 to WAV makes it bigger but does not bring back detail that was already removed.

What each output format contains
FormatDetails
.mp364, 96, 128, 192 or 320 kbps (192 by default). Keeps the sample rate up to 48 kHz; higher rates are resampled to 44.1 or 48 kHz
.m4aAAC in an MPEG-4 file, 96–256 kbps (128 by default). Needs an AAC encoder in the browser (WebCodecs)
.opusOpus in an Ogg file, 48–192 kbps (96 by default). The tool encodes Opus at the source rate when it is 8, 12, 16, 24 or 48 kHz, otherwise at 48 kHz. Needs an Opus encoder in the browser
.wavUncompressed 16-bit PCM at the source sample rate. No quality setting

Speed, pitch and volume

  • “Speed” goes from 0.5× to 2× in 0.05 steps. At 2× the file is half as long; at 0.5×, twice as long.
  • With “Keep pitch” on (the default), the tool time-stretches: it lays short overlapping pieces of about 46 ms back together at a new pace, picking each piece so it lines up with the one before. Voices and instruments keep their pitch.
  • With “Keep pitch” off, speed and pitch change together, like a tape played faster or slower.
  • “Volume” goes from 50% to 200%. When a boost would push peaks above −1 dBFS, a limiter holds them there, and a note under the waveform says so. If the limiter had to work, the export summary shows by how much, for example “limiter −3.0 dB”.

Questions

Why is M4A or Opus greyed out?
Those formats are encoded with the browser’s WebCodecs encoders, and your browser did not offer one. MP3 and WAV are encoded by the tool itself and always work.
Why does the converted file have a different sample rate?
Each encoder accepts only some rates. MP3 goes up to 48 kHz, Opus is encoded at 8, 12, 16, 24 or 48 kHz, and AAC uses the source rate when the browser’s encoder accepts it, otherwise 44.1 or 48 kHz. WAV always keeps the source rate.
Is my file uploaded?
No. Decoding, speed and volume changes, and encoding all run in your browser tab.